COMPLIANCES
Meets or exceeds the requirements of FAA Material Specification Item P-606.
VOC Compliant (<50 g/L)
Appearance:
Component A– white, Component B– black
Shelf Life:2 years in original unopened container
Storage Conditions: Store at 40°- 95°F (5°- 35°C).
Condition material to 65°- 85°F (18°- 29°C) before using
Gel Time (60 g mass): 45 min at 73° ± 2°F (23°C)
Minimum substrate temperature for application: 55°F (13°C)
Mix Ratio: 1:1 by volume
Packaging
1 gal./3.8 L units (two .5 gal. cans)
2 gal./7.6 L units (two 1 gal. cans)
10 gal./37.9 L units (two 5 gal. pails)
110 gal./416.4 L units (two 55 gal. drums)
MIXING/APPLICATION
Mix equal parts by volume of component A and component B with low speed drill and Jiffy mixer at 200-300 rpm for exactly 3 minutes until thoroughly blended.
Mix only quantities that can be used immediately.
Cleanup
Ventilate area. Confine spill. Collect with absorbent material, flush area with water. Dispose of in accordance with current applicable local, state and federal regulations. Uncured material can be removed with Unitex Citrus Cleaner or other approved solvent. Cured material can only be removed mechanically.
|
Properties
|
LABORATORY TESTS |
RESULTS |
ITEM P-606 SPECIFICATIONS |
|
Mix Ratio |
1 : 1 by volume |
- |
|
Shelf Life |
Two years |
- |
|
Color Part A
Part B |
White
Black |
- |
|
C-881 Gel Time |
45 Minutes |
- |
|
D-2393 Brookfield Visc. RV3 @ 20 rpms |
1,000 cps |
- |
|
ASTM D 695 Compressive Yield Strength |
5,000 psi |
- |
|
D-695 Compressive Modulus |
120,000 psi |
- |
|
D-638 Tensile Strength |
1,500 psi |
1,000 psi minimum |
|
D-638 Tensile Elongation |
65% |
50% minimum |
|
ASTM D1168 Coefficient of Cubic Expansion |
0.0010 cm3/cm3 /Co |
0.00090-0.00120 |
|
ASTM D1168 Coefficient of Linear Expansion |
0.00033 cm/cm/Co |
0.00030-0.00040 |
|
ASTM D 149 Dielectric Strength |
410 volts/mil |
350 minimum |
|
ASTM D 495 Arc Resistance |
135 seconds |
125 minimum |
|
ASTM D1002 Adhesion to Steel |
1,250 psi |
1,000 minimum |
|
ACI 503 R Adhesion to Concrete |
350 psi |
200 minimum |
|
ASTM D 570 Water Absorption 24 hours |
0.20% |
- |
|
ASTM D 570 Jet Fuel Absorption 24 hours |
0.10% |
- |
|
ASTM D 2240 Shore D Hardness |
72 |
- |
|
ASTM C 884 Thermal Compatibility |
Pass |
- | |
First Aid
Remove contaminated clothing. For eye contact, flush immediately with plenty of water for at least 15 minutes; contact physician immediately. For respiratory problems, remove person to fresh air. For skin contact, remove epoxy immediately with a dry cloth or paper towel. Wash area of contact thoroughly with soap and water. Solvents should not be used because they carry the irritant into the skin. Wash clothing before re-use. Cured epoxy resins are innocuous. |
Cautions
Component "A" Irritant: Prolonged contact with skin may cause irritation. Avoid eye contact.
Component "B" Corrosive: Contact with skin may cause severe burns. Avoid skin contact.
Product is a strong sensitizer. Use of safety goggles and chemicalresistant gloves recommended. Avoid breathing vapors. Use adequate ventilation. Use of a NIOSH/MSHA organic vapor respirator recommended if ventilation is inadequate. |