|
DOWNLOADS:
Compliances
ASTM C881-90, Type III, Classes B & C
Meets USDA specifications for use in food-processing areas |
A solvent-free, moisture-insensitive, 100% solids, low-modulus, two-component bonding agent. Meets ASTM C881, Type III, Grade 1, Classes B & C. Also meets USDA specifications for use in food processing areas.
Excellent for use as a binder for concrete skid-resistant overlays on bridges and elevated slabs.
Features
Meets AASHTO-AGC-ARTBA
Excellent bond strength
Moisture insensitive, nonflammable
High early strength
Easy to mix - 1:1 ratio
Low modulus, low viscosity
Link to product TEST DATA |
 |
Usage
- Bonding skid-resistant overlays to bridges and elevated slabs
- For use in epoxy mortar for patching
- For use as a low-modulus bonding agent
Coverage
|
Minimum Epoxy & Aggregate Coverage Rates |
|
|
Epoxy Rate |
Aggregate Rate |
|
Course 1 |
1 gal./40 sq. ft. (1 L/sq. M) |
10 lbs./sq. yd. (5.4 kg/sq. M) |
|
Course 2 |
1 gal./20 sq. ft. (2 L/sq. M) |
14 lbs./sq. yd. (7.6 kg/sq. M) |
|
Mortar Coverage Rates |
|
|
Mixed Epoxy/Aggregate Rate |
|
|
1 gal./808 cu. in. (3.8 L/317 cu. cm) |
Packaging
1 gal./3.8 L units (two .5 gal. cans)
2 gal./7.6 L units (two 1 gal. cans)
10 gal./37.9 L units (two 5 gal. pails)
110 gal./416.4 L units (two 55 gal. drums)
|
Application
Bonding Skid-Resistant Overlays:
|
1 |
Repair delamination, potholes and cracks with PRO-POXY 2500. |
|
2 |
Clean surface by shot blasting to remove all contaminants. Remove dust and debris by blowing off with oil-free compressed air. |
|
3 |
See Limitations for required minimum product and application temperatures. Mechanically mix component A with component B 1:1 by volume with Jiffy type mixer and low-speed variable drill at 300 rpm for a minimum of 3 minutes. Mix only the quantity that can be used within its gel time. |
|
4 |
Apply neat PRO-POXY Type III DOT by notched squeegee at the specified rate. |
|
5 |
Broadcast select aggregate to refusal. The aggregate should be angular grain silica sand or basalt having less than 0.2% moisture and free of dirt, clay, etc. The silica sand or basalt should have a minimum Mohs scale hardness of 7 unless otherwise approved. |
|
6 |
After initial cure of first course, remove excess aggregate. Do not open to traffic. |
|
7 |
Apply second course of epoxy and aggregate. Remove excess aggregate. Allow to cure following the table below. Open to traffic. | |
|
Minimum Curing Times of PRO-POXY Type III DOT Overlay |
|
|
Average Temperatures of Overlay Component & Substrate (See Limitations for minimum temperatures) |
|
Min. Cure Time |
60-64°F
16-18°C |
65-69°F
19-21°C |
70-74°F
22-23°C |
75-79°F
24-26°C |
80-84°F
27-29°C |
85+°F
29+°C |
|
Course 1 |
4 hrs |
3 hrs |
2.5 hrs |
2 hrs |
1.5 hrs |
1 hr |
|
Course 2 |
5-6 hrs |
5 hrs |
4 hrs |
3 hrs |
3 hrs |
3 hrs | |
|
|
|
|
|
|
Resin Properties
|
Laboratory Tests |
Results |
ASTM C881 Specifications |
|
Mix Ratio |
1:1 by volume |
-- |
|
D-695 Compressive Modulus |
80,000 |
130,000 maximum |
|
D-638 Tensile Strength |
3,000 psi |
-- |
|
D-638 Tensile Elongation |
50% |
30% minimum |
|
C-882 Bond Strength (14-day cure) |
3,200 psi |
1,500 psi minimum |
|
D-570 Absorption |
0.2% |
1.0% maximum |
|
C-881 Gel Time |
15 minutes |
-- |
|
C-881 Brookfield Visc RV3 at 20 rpm |
1,425 cps |
2,000 cps maximum |
|
D-2240 Shore D Hardness |
69 |
-- |
|
C-883 Shrinkage |
Pass |
Pass |
|
C-884 Thermal Compatibility |
Pass |
-- |
|
AASHTO-T-277 Chloride Ion Permeability |
0.9 coulombs |
-- |
|
|
Grout Properties
Sand to resin – 3.5:1 by volume |
|
Laboratory Tests |
Results |
ASTM C-881 Specifications |
|
C-579 Compressive Strength 3 hrs (2) |
1,100 psi |
N/A |
|
C-579 Compressive Strength 24 hrs (2) |
7,500 psi |
N/A |
|
C-579 Compressive Strength 48 hrs, moist cure (2) |
7,000 psi |
N/A |
1 Class B
2 C-579 Method B with plastic inserts | |
|
Limitations
Not for use on exterior slabs on grade subject to freezing.
Do not thin with any solvents.
PRO-POXY TYPE III DOT is a vapor barrier after cure.
Minimum age of concrete must be 28 days before applying as an overlay.
Minimum age of concrete must be 5-7 days, depending on curing and drying conditions before applying as a mortar.
Minimum substrate and ambient temperature should be
55°F and rising by 10am.
Minimum epoxy temperature should be 65°F before
application.
Shelf Life - 2 years in original unopened container. |
Cleanup
EQUIPMENT: Uncured material can be removed with Unitex CITRUS CLEANER or other approved solvent. Cured material can only be removed mechanically.
MATERIAL: Collect with absorbent material. Flush area with water. Dispose of in accordance with local, state and federal disposal regulations. |
|
First Aid
EYE CONTACT: Flush immediately with water for at least 15 minutes. Contact physician immediately.
RESPIRATORY CONTACT: Remove person to fresh air.
SKIN CONTACT: Remove any contaminated clothing. Remove epoxy immediately with a dry cloth or paper towel. Solvents should not be used as they carry the irritant into the skin. Wash skin thoroughly with soap and water.
CURED EPOXY RESINS ARE INNOCUOUS. |
Cautions
Component A - Irritant
Component B - Corrosive
Product is a strong sensitizer. Use of safety goggles and chemical resistant gloves are recommended.
Use of a NIOSH/MSHA organic vapor respirator is recommended if ventilation is inadequate.
Avoid breathing vapors.
Avoid skin contact. |